---

 

TPZ molecular adhesive polymer film based waterproof membrane series

 

---

 

product description

 

The high-performance resin film made of automobile explosion-proof membrane is used as the base of the tire. The two sides are coated with a unique patented technology. The self-adhesive asphalt layer can be bonded with the base layer at the molecular level. The lower surface is covered with a point-breaking separator and the upper surface. Covered with a Dura fiber reinforced mesh, it is a waterproof membrane that can be directly lashed with steel without a protective layer.

---

 

Features

 

●Central car explosion-proof membrane material base

The material has both high strength of resin and high elongation of PE, and the waterproof membrane is made of:

Material stability - high and low temperature are not wrinkle; extension high - adapt to the deformation of the base layer; high strength - strong resistance to damage, can be protected from the protective layer, directly tied steel.

 

●The material supports the synchronous floor water construction of the underground floor, saving the construction period, saving the cost, and saving the process.

 

●Molecular-grade self-adhesive rubber - Daxie's unique patented technology formula

A hydrophilic auxiliary agent is added to the gum. The hydrophilic group generates a stable ionic bond and a hydrogen bond by generating a bond with the hydration product of the cement paste, so that the waterproof layer and the base layer form a stable and durable molecular-level adhesive sealing effect.

After forming anti-sticking with the underground reinforced concrete self-waterproof structure, it can eliminate drowning and realize zero leakage underground engineering.

The self-adhesive layer body can be bonded at -20 °C, bonded in water, and constructed under full meteorological conditions to ensure the construction period and quality.

●The self-adhesive layer body can be bonded at -20 °C, bonded in water, and constructed under full meteorological conditions to ensure the construction period and quality.

 

●The self-adhesive layer has good creep properties, can release stress, and adapts the coil to deformation without being cracked.

 

---

 

Specification model

 

Reinforcement material	Polymer film base（P）
Upper surface material	Single-sided fiber reinforced（S）
thickness	1.5mm/2.0mm
width	1000mm
length	15m/20m

 

---

 

Scope of application

 

It is especially suitable for the waterproofing of basement (anti-stick) and basement side wall (outside anti-adhesive, anti-adhesive) of industrial and civil buildings with high groundwater and high risk of leakage.

This product is the savvy choice for customers who suffer from leakage from the basement floor and pay attention to the final non-seepage effect of the basement.

 

---

 

Construction process

 

Pour the cushion for 4~6 hours, and then spread the TPZ molecular viscose anti-adhesive waterproofing membrane after the conditions can be applied.

Formulating glue

>>According to the temperature and humidity, add appropriate amount of water to the batching bucket according to the water-cement ratio of 0.35~0.40, add 42.5Mpa ordinary Portland cement, stir well with electric stirrer until it is even, fine and free of lumps.

Trial roll

>>Wrap the coil on the base surface, align the elastic wire or the overlapping edge of the adjacent coil to ensure the overlap width, and release the stress after re-winding.

Scrape

>>The glue is applied to the base layer (planar) or scraped and bonded to the coil (facade) with a thickness of 2~3mm.

Paving coil

>> Roll the material forward while peeling off the bottom separator.

Squeeze exhaust

>> Use the matching tools to push the surface of the coil and extrude the internal gas, so that the coil, the glue and the base layer are completely bonded.

Body lap

>> After the rubber layer reaches the strength of the upper body, the lap joint separator is torn off, and the press roller is compacted to realize the lap joint of the coil body.

After the coil is laid for 1 day, the strength of the glue can be directly tied to the surface of the coil without the need for pouring a protective layer.

 

---

 

Engineering case

 

Click on the link to the project case

 

---

 

Performance

 

Perform "TPZ fiber reinforced wet shop / pre-laid waterproofing membrane" QLDY 0006-2016.

pull	≥500N/50mm
Elongation	≥150%
Tear strength	≥25N
Heat resistance	70℃,2h No displacement, runny, dripping
Low temperature compliance	-25℃ No crack
Impervious	0.3MPa，120min impermeable
Peel strength (coil and coil)	≥1.0N/mm（No treatment）
Peel strength (coil and cement mortar)	≥2.0N/mm（No treatment）
Impact performance	Diameter (10±0.1mm) without leakage
Anti-hydrophobic	0.4MpaInnocent water

 

---